Showing results: 1591 - 1605 of 2536 items found.
-
TOELLNER-wavecontrol -
Toellner Electronic Instrumente GmbH
The Software TOELLNER-WaveControl provides waveforms and controls the TOELLNER system components at the test station, which can be individually tailored to your requirements. Using a DAQ-Card, any signal waveform can be provided with Arbitrary Power Supplies or 4-Quadrant Amplifiers with outputs from 160 W to 5200 W. For fast interruptions, TOELLNER offers electronic switches with switching times below 500 ns.
-
Keysight Technologies
Early in the RFIC design phase, monitoring system IC specifications such as EVM via RF simulation is a must. Simulations include effects of layout parasitics, complex modulated signals, and digital control circuitry. With PathWave RFIC Design, you can simulate in both the frequency and time domain and bring your designs to and from Cadence Virtuoso and Synopsys Custom Compiler.
-
79G5 -
North Atlantic Industries
NAI's latest generation single-slot, half-size PCIe board, the 79G5 can be configured with up to three NAI intelligent I/O and communication function modules. Ideally suited for high channel density and combined multifunction I/O requirement systems, the 79G5 delivers off-the-shelf solutions that accelerate deployment of digital and analog I/O, position control and measurement/simulation and communication interface applications.
-
Model 9009 -
ICS Electronics
* All interfaces provide full control of the Modbus RTU slave devices.* Ethernet port supports VXI-11, raw socket and Modbus TCP/IP to Modbus RTU conversion. * GPIB port works with any IEEE-488.2 compatible GPIB controller.* USB port uses Microsoft supplied driver to prevent operating system change problems.* The 9009 uses a simple command set that is accessible from any port.* Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls. Works with Agilent, NI and Kikisui VISA libraries* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* Ethernet interface protocol is fully VXI-11 compliant and does not require special PC drivers.* Internal webserver with sample Modbus device control pages for Watlow F4, F4T and EZ-Zone Controllers.* OEM oriented board designed for integration inside the user's system with only one cable. On board regulator works with 5 to 15 Vdc power.* Support programs Include ICS's VXI-11 and VISA keyboard control programs and a NTML page utility for uploading your customer webpages.
-
NI
The Analog Output Device helps you create applications such as stimulus-response, power supply control, deterministic control, and sensor/signal simulation. The Analog Output Device supports various output resolutions, channel counts, and other onboard features, so you can replace several kinds of instruments in your system, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators.The Analog Output Device includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Analog Devices Inc.
Analog Devices provides a range of analog microcontrollers featuring ARM® Cortex™-M3 processors that help enable this product portfolio’s high precision, high performance, and low cost. By featuring ARM Cortex-M3 processors, our devices include a rich support system to aid product development throughout applications that include optical networking, industrial control, point-of-care diagnostics, and a variety of other industrial, instrumentation, and medical uses. Precision analog blocks including, but not limited to ADCs, DACs and references allow for precision control and measurements. Included also is the ability to read back diagnostics, which is a key requirement in the above applications.
-
NI
The Voltage Input Module for Remote I/O features 2-, 3-, and 4-wire spring terminal connection methods, a built-in power supply for sensors, four selectable input ranges, and simultaneous sampling. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Voltage Input Module for Remote I/O from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements.
-
Yelo Ltd.
Yelo has a wealth of experience in developing and customizing test systems for the Travelling Wave Tube (TWT) market. TWT testers feature specialized power supplies, measurement equipment, and comprehensive control and safety systems.A rugged PLC is used to control all voltages and perform all monitoring functions. User interface and datalogging functions are provided by a supervisory PC that is electrically isolated from the PLC. Power Supplies are solid state with optical fibre barriers to ensure that all control/monitoring is carried out at safe voltages, and with maximum noise immunity. All safety interlocks are hardwired, and the testers are equipped with emergency shutdown features for added security.
-
Rotor Starter -
Hilkar
The Slip-Ring Motor Starters are based on the series of resistors that are applied to the rotor circuit to control the speed/torque characteristics of the motor. Rotor starters are mainly used for the motor starting applications requiring high-starting torque like loaded belt conveyors in mining industry. By external resistors, it is possible to shift the motor maximum (break-down) torque up to starting torque point for motors under heavy loads during start-up. The resistors are splitted into some steps and controlled via contactors by motor starting control system. As the motor speed increases, the external rotor resistors are eliminated by shorting contactors until all external resistors are shorted out.
-
M8085A -
Keysight Technologies
The M8085A is a software plug-in for M8070A Bit Error Ratio Test system software within the M8000 series of BER test solutions. The M8085A software plug-in controls either the M8190A or the M8195A Arbitrary Waveform Generators to create C-PHY or D-PHY standard compliant test signals. In addition it provides routines for calibration of all signal parameters and for all tests specified in the applicable Conformance Test Suite. Together with the additional available DUT control interface it is possible to read the BER of the receiver under test from the M8070A software and display the BER dependency from test parameters within the M8070A user interface.
-
Leuze electronic GmbH + Co. KG
The CMS 700i 3D contour measurement system detects the length, width, height, deformations and position of any objects as they pass by, independent of their shape and surface. Even polybags are reliably detected. The complete system includes all components for operation and installation under one part number. In contrast, light section sensors record a height profile along a projected laser line. This allows objects to be detected with high resolution in multiple dimensions. The integrated functions range from presence control to edge measurement and 3D object measurement.
-
Ajinkya Electronic Systems
Ajinkya Electronic Systems has developed Microprocessor based programmable energy saver system. Voltage Control Panel is a unique concept guaranteed to provide a saving between 20 to 45 % in electrical energy consumption. Energy conservation is a movement that is compelling the world to take serious steps to avert loss of energy. The Ajinkya ESS is a boon to the modern industrial world in the sense that it helps in saving substantial amount of electrical energy used for the purpose of lighting like tube lights, mercury vapor lamps & sodium vapour lamps etc.
-
National Technical Systems
NTS’ Fuel Systems & Component Testing site at Santa Clarita is used for the development and qualification of fuel line parts and subsystems. Any individual device or subsystem that is part of an engine or fuel system – such as fuel pumps, hydro-mechanical fuel controls and shutoff valves – requires qualification testing to the RTCA DO-160 environmental standards for airborne equipment or the Mil-STD 810G environmental standards for a broad range of military equipment. The fuel testing site installed at NTS Santa Clarita is a state-of-the-art facility for simulating the most stringent environmental conditions.
-
Aceonn Corp.
Aceonn can integrate your existing laboratory equipment to improve data reliability, repeatability and responsibility: Reliability comes from setting test equipment via electronic controls; minimizing human error; Repeatability ensures that all tests for every device is performed to the same exact specifications; Responsibility flourishes in an environment that utilizes state-of-the art test systems. Aceonn will streamline your laboratory’s testing process and make your business more efficient. There is no need to buy new test equipment, just a better communication system.
-
Teledyne Marine PDS
Allows a 3D Scanning sonar user to collect motion compensated 3D point clouds from a moving platformTeledyne PDS MotionScan system allows a 3D Scanning sonar user to collect motion compensated 3D point clouds from a moving platform. The MotionScan system is comprised of: an RTK capable dual antenna GPS with precision heading output, a heave, pitch and roll sensor, a topside control console. In combination with a BlueView 3D Multibeam Scanning Sonar this creates a full survey package.
